Go to the source code of this file.
| #define SC_TDC_ERR_DEFAULT -1 |
General or unknown error.
| #define SC_TDC_ERR_INIFILE -2 |
| #define SC_TDC_ERR_TDCOPEN -3 |
| #define SC_TDC_ERR_NOMEM -4 |
System has not enough memory to perform operation.
| #define SC_TDC_ERR_SERIAL -5 |
| #define SC_TDC_ERR_TDCOPEN2 -6 |
| #define SC_TDC_ERR_PARAMETER -7 |
| #define SC_TDC_ERR_SMALLBUFFER -8 |
| #define SC_TDC_ERR_BADCONFI -9 |
Inifile cannot be found or has incorrect syntax.
| #define SC_TDC_ERR_NOTINIT -10 |
Device is not initialized or bad device descriptor.
| #define SC_TDC_ERR_NOTRDY -11 |
Device is not ready to operate.
| #define SC_TDC_ERR_DEVCLS_LD -12 |
Could not load device class library. Insure that it is present, has correct architecture string and dependencies.
| #define SC_TDC_ERR_DEVCLS_VER -13 |
Device class library has unsupported version. Update or use appropriate version.
| #define SC_TDC_ERR_DEVCLS_INIT -14 |
Could not initialize device class library. Insure that firmware file is present.
| #define SC_TDC_ERR_FPGA_INIT -15 |
Could not initialize fpga. Insure that firmware file is present and correct.
| #define SC_TDC_ERR_ALRDYINIT -16 |
Subsystem is already initialized. To reinitialize deinitialize first.
| #define SC_TDC_ERR_TIMEOUT -17 |
Timeout during data read.
| #define SC_TDC_ERR_NOSIMFILE -18 |
No simulation data file found. Insure that it is present and correct.
| #define SC_TDC_ERR_SPURIOUS_WAKEUP -19 |
| #define SC_TDC_ERR_SYNC -20 |
| #define SC_TDC_ERR_GPX_RST -21 |
Could not reset GPX. Communication with GPX broken.
| #define SC_TDC_ERR_GPX_PLL_NLOCK -22 |
| #define SC_TDC_ERR_USB_COMM -30 |
| #define SC_TDC_ERR_CORR_SET -40 |
| #define SC_TDC_ERR_ROI_SET -42 |
| #define SC_TDC_ERR_FMT_SET -43 |
| #define SC_TDC_ERR_FMT_UNSUPPORT -44 |
| #define SC_TDC_ERR_ROI_BAD -45 |
| #define SC_TDC_ERR_ROI_TOOBIG -46 |
| #define SC_TDC_ERR_BUFSIZE -47 |
- Deprecated:
- returned from sc_tdc_alloc_buffer() and sc_tdc_alloc_buffer_v()
| #define SC_TDC_ERR_GPX_FMT_UNSUPPORT -48 |
| #define SC_TDC_ERR_GPX_FMT_SET -49 |
| #define SC_TDC_ERR_FMT_NDEF -50 |
- Deprecated:
- returned from sc_tdc_alloc_buffer() and sc_tdc_alloc_buffer_v()
| #define SC_TDC_ERR_FIFO_ADDR_SET -60 |
Unable to set fifo reading address
| #define SC_TDC_ERR_MODE_SET -61 |
| #define SC_TDC_ERR_START_FAIL -62 |
Could not start gpx reading
| #define SC_TDC_ERR_TIMER_SET -63 |
| #define SC_TDC_ERR_TIMER_EX_SET -64 |
Unable to set time range extender
| #define SC_TDC_ERR_STRT_FREQ_DIV_SET -65 |
Unable to set start frequency divider
| #define SC_TDC_ERR_STRT_FREQ_PERIOD_SET -66 |
Unable to set start frequency period
| #define SC_TDC_ERR_TWI_NO_MODULE -70 |
TWI module is not available
| #define SC_TDC_ERR_TWI_FAIL -71 |
Unable to operate TWI module
| #define SC_TDC_ERR_TWI_NACK -72 |
No acknowledge received from TWI slave
| #define SC_TDC_ERR_POT_NO -73 |
Digital potentiometer is not available
| #define SC_TDC_ERR_POT_SET -74 |
Cannot set digital potentiometer
| #define SC_TDC_ERR_FLIM_PARM_SET -80 |
Cannot set FLIM scanner parameters
| #define SC_TDC_ERR_OPEN_LINE_CORR_FILE -81 |
Cannot open line_cor.txt file
| #define SC_TDC_ERR_WRONG_LINE_CORR_FILE -82 |
| #define SC_TDC_ERR_CONNLOST -90 |
No connection to the device
| #define SC_TDC_ERR_CMOS_REG -95 |
Unable to set/get CMOS register
| #define SC_TDC_ERR_NO_LIBRARY -96 |
| #define SC_TDC_ERR_NO_LIBRARY_SYM -97 |
Could not find library symbol
| #define SC_TDC_ERR_SYSTEM -1000 |
No enough resource available
| #define SC_TDC_ERR_NOT_IMPL -9000 |
| #define SC_TDC_ERR_NO_HARDWARE_SUPPORT -9001 |
Feature not supported by hardware
| #define SC_TDC_INFO_MEAS_COMPLETE 1 |
| #define SC_TDC_INFO_USER_INTERRUPT 2 |
| #define SC_TDC_INFO_BUFFER_FULL 3 |
| #define SC_TDC_INFO_HW_IDLE 4 |
Hardware finished measument and is in idle state
